Support
Wir sind für Ihre Fragen da
Anleitungsvideo
Benutzeraneitung
Batteriesanierungsservice
Benutzeraneitung
Batteriesanierungsservice
BuWizz verfügt über einen internen Lithium-Polymer-Akku, der sich wie alle Akkus mit der Zeit und dem Verbrauch verschlechtert (Lade- / Entladezyklen).
Wir haben Batterien vieler Hersteller getestet und verwenden in allen BuWizz-Produkten erstklassige Batterien. Unsere Tests haben gezeigt, dass BuWizz-Batterien mehr als 2.000 Lade- / Entladezyklen aushalten können, bevor die Kapazität auf 80% der ursprünglichen Kapazität abfällt (Industriestandard zur Bestimmung der Batterielebensdauer). Dies bedeutet mehrere tausend Stunden Spielzeit oder viele Jahre Alltagsgebrauch. Und selbst bei 80% der ursprünglichen Kapazität ist der Akku noch nicht leer. Nur die Laufzeit zwischen den Ladevorgängen wird proportional verkürzt, aber Sie können Ihren BuWizz weiterhin verwenden.
BuWizz Legacy App
BuWizz App (Open Beta) – Gamepad Support Instructions
BuWizz App with support for LEGO Technic Powered Up HUB
BuWizz Bluetooth®
protocol
Common issues
Tips & Tricks
FAQ
LED indicator
Why is Buwizz LED shining/blinking green?
Battery level between full and 2/3
Why is Buwizz LED shining/blinking orange?
Battery level is between 2/3 and 1/3
Why is Buwizz LED shining/blinking red?
1. Battery level is under 1/3
2. Recharge Buwizz
Why is Buwizz LED quickly blinking red/green?
1. Quick blinking of red and green LED means battery is critically low
2. Recharge Buwizz
Buwizz's LED is quickly blinking red
BuWizz firmware issues. New firmware is in the works and scheduled to be released in July 2018
Troubleshooting
PU Ports 1&2 and 3&4 are blinking RED/GREEN alternately All PU ports are blinking in a RED spinning pattern
Hold the power button
for 5 seconds to reset the
BuWizz alternately
All PU ports are blinking in a RED spinning pattern
Buwizz will not turn off when pressing the button
1. Buwizz is connected to the app and will therefore not turn off
2. Close Buwizz app and try turning off Buwizz again
3. If Buwizz still does not turn off, turn off Bluetooth on your phone and try turning off Buwizz again
Buwizz does not turn on when pressing the button
1. Charge Buwizz for 3 hours
2. Check your charger and cable are working properly
3. Note, BuWizz turns off automatically during charging. No LED is lit, but charging still continues
4. In case Buwizz still does not turn on after charging for 3 hours, contact technical support
Buwizz will not pair with the phone
1. DO NOT pair Buwizz with bluetooth
2. Pairing should not be performed
3. Use Buwizz app to connect
Buwizz is not visible in the app
1. Check your device is compatible with the Buwizz app (Bluetooth 4.0 or higher), running Android 4.4 or higher.
2. Give Buwizz app permission to access location information
3. Turn on bluetooth
4. Make sure your device is not outside the Bluetooth range – suggested range for detection of Buwizz is under 5 meters
5. In case the problem persists, contact technical support
Buwizz is visible in the app, but will not connect
1. Make sure to wait for the scan for devices to be completed before staring the engine button in the Buwizz app.
2. Make sure your device is not outside the Bluetooth range – suggested range for detection of Buwizz is under 5 meters
3. Turn off Buwizz for 3 seconds and try reconnecting
4. Restart the Buwizz app
5. In case the problem persists, contact technical support
Buwizz works but at extremely low rangeHow will my shirts ship?
My model loses connection when accelerating, braking or reversing in high speed/ludicrous mode
1. Buwizz’s internal overcurrent protection is tripping due to the current spikes due to the fast speed changes
2. Do not connect more than 2x XL, 2x L, 2x M or 1x RC motor per output
3. Make sure to control motors carefully, avoiding quick speed changes and reversals of the power sliders.
4. In cases where swift control and reversals of motors are needed, use Slow or Normal mode.
5. Run several BuWizz bricks in parallel to increase number of motors running in parallel for huge models.
App connects to Buwizz, but after a while model stops responding
1. Buwizz will stop responding if the model leaves the range – for best performance keep your model with 15 meters of range
2. Battery is empty – recharge Buwizz
3.Under heavy load and drained battery, Buwizz will reset itself and terminate connection – recharge Buwizz
Buwizz stops responding when control device has not been used for a while
1. Check that Buwizz is still turned on (BuWizz turns off automatically if no commands are received for 10 minutes)
2. Exit the control profile and reconnect to Buwizz
3. In case of connection issues restart Buwizz or the app
BuWizz will not charge
1. Some newer chargers require communication in order to charge the device which is not possible if the BuWizz is too drained or turned off.
2. Turn on/charge BuWizz with an older charger or via the USB port of a PC.
questions
Is it possible to power 4 lego RC motors with one buwizz?
1. It is possible, but performance will suffer
2. 4x Buggy/RC motors is an extreme setup
3. We recommend using 2x BuWizz.
4. In ludicrous mode, you will experience over-current limiter engaging and your model can stop responding
Why does BuWizz need location permission?
This is an Android requirement, we do not need your location. All apps which use Bluetooth need to have location permission (and Location set to „ON“) or Bluetooth scan does not work
